Currently travelling with a laptop, watch, toothbrush, eReader, camera, bug-bite treater, and phone - all charging from the same power brick.
I'm guaranteed of getting a replacement cable / charger wherever I am in the world if I need it.
The only slight snag is some cheaper itema refuse to use PD and insist on plain 5V/2A - buy most decent travel chargers have NON-PD ports.
Amusingly, most of the buses I've taken recently also have USB-C ports on them for ad hoc charging. Perhaps one day EVs will use USB-PD-Max rather than CCS :-)
I also have assorted products that won't charge c-to-c (some from respectable manufacturers even, like Philips), but I see you can get little adapters with 5.1K resistor you plug into said crappy devices to cover that, I will have to try some out.
I've also returned a few USB devices that ship with a USB-A to USB-C cable and ONLY charge in that mode, they also MUST charge with USB-C PD.
The two so far were a therapy light and some Zippo hand warmers. Like, who in the hell would design a device that has a USB-C port on it where only a fraction of chargers will work on it. It feels even worse than proprietary charges, because you see a USB-C port on it and think, oh I have a plug that fits it, and then it doesn't F**ing work. Idiot engineering/product teams, making the world suck with their falsely advertised USB-C ports. If anyone of you are on a team that ever makes this decision, just know that it is a stupid decision, and jump ship when you can.
It's pure ignorance, not a decision, but the lack of one. Lack of caring, lack of having an actual engineer involved, just slapping an oval-shaped port into a product where a trapezoidal port had been, and blindly thinking that magically makes it spec-compliant.
Or not thinking about the spec at all.
I return these devices too. Lots of them. My e-commerce returns over the last year are probably 50% PD non-compliance, 50% all other defects combined.
By "that mode", do you mean "1.5A @ 5V" permitted by BC, or do you mean "3A @ 20V" permitted by non-type-C PD?
> Like, who in the hell would design a device that has a USB-C port on it where only a fraction of chargers will work on it.
Who in the hell would design a charger that can do Type-C PD but can't do either pre-Type-C PD or BC? Does the charger in question also shit the bed when a USB 1.0 device attempts to draw 100mA @ 5V? I hope not! Were it me, I'd return that crappy thing for a refund.
Lots of people assume that USB-C always uses USB-PD, but the basic signalling is done with resistors. Lots of devices only need 15W, and it is better than USB-A charging. If you want faster charging, buy more powerful chargers.
It has helped out in a bunch of unexpected situations (usually someone else's device)
I bet that cable gets plenty hot at 200+ watts.
There are things that shouldn't be powered by USB-C. But there are plenty of sub 100W consumer electronics devices that really should be USB-C. I waited years before Panasonic released their lamdash shavers using USB-C.
Which is kinda part the issue, usb-c charging bricks, they aren't usb-c power supplies, there is no expectation of sustained output capacity. Thankfully at least some the multiport ones have renegotiation more or less solved cleanly rather than what is essentially rebooting the PD controller.
You reeeeeeally don't want to do that. Cable inductance is a big deal, among other issues. You want the main DC-DC regulators on the board, usually right at the load, for the main loads. Most of the PSU bulk is for dealing with mains itself: handling 50/60Hz or mains isolation is just physically large. Getting in secondary 20V DC (or so) from a single connector and then regulating it down on board is pretty much the ideal solution.
(I can't even begin to comprehend the horrors of a USB-PD negotiation involving multiple voltages. It's already the worst standard I've ever had to deal with.* Don't make it worse!)
(* Not hyperbole, it is truly, truly awful. At least things like 60601 are bad because, you know, they're covering lots of stuff like lifesaving medical devices. USB-PD is... holy hell, it is just bad.)
Lenovo have some,but sometimes require adapter cards. And a few of the Chinese N150 units will take PD power
It's great for hot swapping and more portable than a laptop.
Neither - OP means devices with missing CC resistors which will fail to charge with a compliant PD source. (The A-to-C cable works because it provides 5V Vbus unconditionally.)
So if you are having complete charge failures, try a different cable.
So... yeah.
The bigger issue is not really the parts cost, it's the fact that it adds an extra part to the design that has to be purchased and tracked and assembled and blah blah blah. This is the real reason it often gets left off on the bottom-of-the-barrel products. Many times there is no other use for a 5.1kΩ resistor. And it might not even fit well at the cheap sizes (0603 or 0402), and going down to 0201-capable assembly factory flow just for these two resistors is not going to happen.
5.1k is a surprising resistor value, a lot of modern designs don't really have anything else in that area. I'm often not able to combine anything with it when I'm cost reducing. 4.7k, sure, but there aren't a lot of those either... 2.2k is just not close enough a lot of the time (or ends up as 1k), and same for 10k. So, sadly, it often does stand alone.
But there is some trash out there in the world. A lot of it, actually.
Some naughty cables work with some naughty chargers work with some naughty devices. Postel's Law in action, I guess?
Usually the best place to fix it is by getting rid of the bad cables. Usually.
No. There is no USB-C to C cable that will charge a badly implemented device with a standards compliant charger. That is the entire point.
An USB A to C cable is completely standards-compliant and safe, even if it always supplies 5V on the C end - any standards compliant USB-C device should not activate the MOSFET on its Vbus line unless it successfully negotiates via CC.
I wonder if PD will cause a comeback of that value as more and more legacy device refreshes move to USB-C plugs.